How To Install Lock On Sliding Door

Download Article

Sliding doors are a stylish, modern mode to end your closet. With the right hardware, installing sliding closet doors on your ain is simple. The key to professional-looking doors is taking the correct measurements before your installation.

one

Remove any existing doors on your closet. Use a drill to unscrew whatsoever hinges or tracks from your closet opening, and take off the old doors and set them bated. When you're finished, the opening to your closet should be free of whatsoever obstructions.
two
Measure out the height of your closet opening. Use a tape measure to measure the altitude betwixt the floor and the pinnacle of your cupboard opening to become the peak. Measure the acme several times so y'all know your measurement is accurate.^[ane]
- Write downwards the tiptop somewhere so y'all have it for later.
Advertisement
3

Measure the width of your closet opening. Take the tape measure and mensurate from one side of your closet opening to the other. Measure out the width multiple times to ensure accuracy. When you're finished, write downwards the width so y'all tin refer to it later.^[2]
4
Purchase sliding closet doors and tracks that will fit your closet opening. Sliding closet doors and tracks come up in a diversity of sizes. You'll desire to compare the measurements yous took to the production specifications for the doors and tracks you're looking at then y'all know they'll fit in your closet opening. Look for a gear up of 2 sliding doors that comes with a pair of tracks.
- Expect for doors that are slightly shorter than the height of your closet opening.^[3]
- It'southward OK if the tracks you buy are longer than the width of your closet. You lot can cut them to size later on on. Just make sure the tracks aren't shorter than the width of your cupboard or they'll be too small.
- If yous take a peculiarly broad closet, you may need to buy more than 2 doors. If you lot exercise, look for tracks that can concur 3 or more doors.
Advertising

one
Cut your tracks to size with a hacksaw if needed. Start, subtract 1–two millimetres (0.039–0.079 in) from the width of your cupboard opening using the measurement yous took before. Then, cut the top and bottom tracks to that length. Mark where you demand to cutting the tracks with pencil and then carefully saw forth the line with the hacksaw.^[4]
- When you lot're finished, position the tracks in your closet opening to run across if they fit. If they're yet to large, measure the width of the closet opening over again and cut more than of the tracks off.
2

Position the height track on the top of your closet opening. The top of the track should exist facing downwardly toward the floor. Yous may want to have someone assist you hold the track in place.
iii

Use a drill to screw the track into place. Locate the screw holes along the runway. So, drill the screws that came with the sliding door set into these holes. Make sure you screw them in all the way and then the runway is secure.^[5]
4

Position the lesser runway on the floor of your closet opening. To line the bottom rails up with the acme track, measure out the distance between the side of the meridian track and the front edge of your closet opening. Then, position the bottom rail and then at that place's an equal corporeality of altitude between the side of it and the front edge of the closet opening.^[6]
five
Spiral the bottom track into place. But like you did with the top track, drill the screws that came with the set into the screw holes along the bottom runway. When y'all're finished, the top and bottom track should be securely in place and lined up with each other.^[vii]
- If you lot're flooring is made out of concrete or tile, you'll need to mucilage the bottom track downwards instead of using screws.
Advertizement

1

Insert the wheels on the elevation of the offset door into the tiptop rail. Hold the door so the top is tilted backward. Then, latch the wheels on top of the door onto the back runner of the tiptop rails. The runner is what the wheels coil along then the door can slide back and forth. Each rails has 2 runners — i in the front end and 1 in the back. The first door volition go along the back runners, and the second door will go along the runners in the front of the tracks.^[8]
two

Drop the wheels on the lesser of the door into the bottom track. Line the lesser wheels up with the back runner on the bottom track and and so drop them into place.^[9] Don't accidentally driblet them into the front end runner on the track or the door will exist slanted.^[10]
3

Insert the wheels on the second door into the runners at the front of the tracks. Practise the same affair you did with the offset door, but this time utilize the front runners on the tracks. When you're finished, both doors should slide dorsum and forth forth the tracks without interfering with each other.^[eleven]
four
Suit the doors as needed. Many sliding closet doors can be adapted using the acme and bottom rollers. Use the adjusters to slightly lower or heighten your closet doors, or to make them affluent with the wall.^[12]
- If you lot're not sure how to accommodate your doors, refer to the educational activity manual that came with them.
Advertizement

Add New Question

Question

Practise sliding cupboard doors need a bottom rails?

This reply was written by one of our trained team of researchers who validated information technology for accuracy and comprehensiveness.

wikiHow Staff Editor

Staff Respond

Not necessarily. The lesser track tin can exist useful for guiding the doors when y'all slide them and for keeping them from swinging back and along if someone or something bumps into the door. Nevertheless, lesser tracks don't really support the weight of the doors and aren't necessary for them to role.
Question

How much should sliding closet doors overlap?

This answer was written past one of our trained team of researchers who validated it for accurateness and comprehensiveness.

wikiHow Staff Editor

Staff Answer

They should overlap in the heart by 2-3 inches (5.1-7.half-dozen cm). Without any overlap, yous'll see a gap betwixt the doors and they won't stay on the track properly.
Question

What is a standard sliding closet door size?

This answer was written by one of our trained team of researchers who validated it for accurateness and comprehensiveness.

wikiHow Staff Editor

Staff Reply

Some standard widths are 24, 28, 30, or 32 inches wide (threescore.96, 71.12, 76.2, or 81.28 cm). Nigh closet doors are 80 inches (203.two cm) tall.
Question

How do I level an existing sliding closet door?

Rollers either top or bottom are unremarkably adaptable. Lower types ordinarily take a screw on top that raises the roller when turned clockwise. Upper rollers are sometimes adaptable, but with wooden doors, it depends on how they are mounted and you lot may take to reinstall them a footling to ane side while holding the door in position. Pick one door to be the left or right and adjust it to as flush as possible to that side jamb, then the other to the contrary side.
Question

I have a 96-inch broad opening and need to hang three doors. Will a standard 96-inch track accommodate 3 doors?

Yes. But a door on the left and right side of the back track and one door in the centre of the forepart rails ways yous tin open a little less than ane/3 of the closet at a fourth dimension. Domicile Depot told me that getting a triple rail (for one door per rails and so you tin can access two/3 of a closet at a time) would cost most $190 more than the standard double track and requires more wall depth (a little more than than 5 inches) than I have. If yous desire to stay with 2 doors like I exercise, consider what I am doing. The installer is calculation a few more inches of trim to the sides of the closet -- but plenty to permit 2 48 inch doors overlap. If yous can't lower the bridge, raise the river!
Question

How do I install three doors so that they tin can all slide past each other and all three stack on 1 side?

You would demand to go a triple track and put one door on each rails. As mentioned in a previous question, these tracks can be a bit pricey and crave a bit more wall depth than the standard double track.
Question

Can I employ the molded hollow half dozen-panel door equally a sliding bypass closet door?

Aye, we have 6 panel doors for all our closets. Only ours are not hollow cadre and equally a result, are very heavy, difficult to motility and generally inconvenient. Cute, simply non applied. Hollow core should work better.

Ask a Question

200 characters left

Include your email address to get a bulletin when this question is answered.

Submit

Always wear condom goggles when using a drill or hacksaw.

Advert

Things You lot'll Need

Tape measure out
Sliding doors
Sliding door tracks
Hacksaw
Pencil
Screws
Drill

About This Article

Article Summary Ten

To install sliding cupboard doors, start by screwing the summit track into position at the peak of your door with the rails facing down. Adjacent, screw the bottom track into place or mucilage it downwardly if your floor is fabricated of concrete. One time both tracks are in place, hold up the get-go door, tilt information technology back a piffling, and hook the wheels over the back runner on the top rail. And then, line up the wheels with the back runner on the lesser track and drop them into place. Finally, hook the wheels on the second door into the front runner on the top and bottom tracks. To notice out how to adjust your doors and what to do if your tracks are besides wide, read on!

Did this summary help you?

Thank you to all authors for creating a folio that has been read 200,883 times.